CVE-2026-75084 (GCVE-0-2026-75084)
Vulnerability from cvelistv5 – Published: 2026-10-14 16:46 – Updated: 2026-10-14 16:46
VLAI
EPSS
VEX
Title
Out-of-bounds write in the TI CC1200 IEEE 802.15.4 driver from an unvalidated radio-supplied packet length
Summary
The CC1200 sub-GHz IEEE 802.15.4 driver takes the PHY packet length from the first byte of the radio's RX FIFO in get_packet_length() and validates it in verify_rxfifo_validity() (drivers/ieee802154/ieee802154_cc1200.c). That validation only enforced a lower bound (pkt_len < 3); its second clause rejects a FIFO that holds more bytes than declared and therefore never bounds large values. Because the driver configures the radio for variable packet length with PKT_LEN = 0xFF, the length byte is an over-the-air value of 0-255 that reached net_pkt_rx_alloc_with_buffer() and the subsequent SPI burst read unclamped.
An unauthenticated attacker within radio range can transmit a frame that presents a length byte above the IEEE 802.15.4 maximum of 127 while the chip's 128-byte RX FIFO has not overflowed, so the driver's RX_FIFO_ERROR pre-check does not fire. Reaching this state depends on RF framing and timing, since the RX thread is driven off the PKT_SYNC_RXTX signal and may sample the FIFO before a packet is complete; no pairing, authentication, or user interaction is required.
With the default CONFIG_NET_BUF_FIXED_DATA_SIZE and CONFIG_NET_BUF_DATA_SIZE=128, an allocation larger than one fragment is satisfied by a chain of fragments, but read_rxfifo_content() performs a single SPI burst of pkt_len bytes into the first fragment's buf->data and then calls net_buf_add() with the same length. A length above 128 therefore writes up to 127 bytes past the end of a fragment in the contiguous rx_bufs pool and leaves a net_buf whose len exceeds its capacity. The overflowing bytes are FIFO-underflow output rather than attacker-chosen data, so the practical impact is network-buffer-pool corruption and crashes rather than a controlled write. Only builds that enable CONFIG_IEEE802154_CC1200 with an attached CC1200 radio are affected.
Severity
6.8 (Medium)
CWE
- CWE-787 - bounds
Assigner
References
2 references
Impacted products
1 product
| Vendor | Product | Version | CPE status | |
|---|---|---|---|---|
| zephyrproject | zephyr |
Affected:
1.11.0 , ≤ 4.4.2
(semver)
|
guessed |
{
"containers": {
"cna": {
"affected": [
{
"collectionURL": "https://github.com/zephyrproject-rtos/zephyr",
"defaultStatus": "unaffected",
"packageName": "zephyr",
"product": "zephyr",
"programFiles": [
"drivers/ieee802154/ieee802154_cc1200.c"
],
"programRoutines": [
{
"name": "cc1200_rx"
},
{
"name": "read_rxfifo_content"
},
{
"name": "verify_rxfifo_validity"
}
],
"vendor": "zephyrproject",
"versions": [
{
"lessThanOrEqual": "4.4.2",
"status": "affected",
"version": "1.11.0",
"versionType": "semver"
}
]
}
],
"descriptions": [
{
"lang": "en",
"value": "The CC1200 sub-GHz IEEE 802.15.4 driver takes the PHY packet length from the first byte of the radio\u0027s RX FIFO in get_packet_length() and validates it in verify_rxfifo_validity() (drivers/ieee802154/ieee802154_cc1200.c). That validation only enforced a lower bound (pkt_len \u003c 3); its second clause rejects a FIFO that holds more bytes than declared and therefore never bounds large values. Because the driver configures the radio for variable packet length with PKT_LEN = 0xFF, the length byte is an over-the-air value of 0-255 that reached net_pkt_rx_alloc_with_buffer() and the subsequent SPI burst read unclamped.\n\nAn unauthenticated attacker within radio range can transmit a frame that presents a length byte above the IEEE 802.15.4 maximum of 127 while the chip\u0027s 128-byte RX FIFO has not overflowed, so the driver\u0027s RX_FIFO_ERROR pre-check does not fire. Reaching this state depends on RF framing and timing, since the RX thread is driven off the PKT_SYNC_RXTX signal and may sample the FIFO before a packet is complete; no pairing, authentication, or user interaction is required.\n\nWith the default CONFIG_NET_BUF_FIXED_DATA_SIZE and CONFIG_NET_BUF_DATA_SIZE=128, an allocation larger than one fragment is satisfied by a chain of fragments, but read_rxfifo_content() performs a single SPI burst of pkt_len bytes into the first fragment\u0027s buf-\u003edata and then calls net_buf_add() with the same length. A length above 128 therefore writes up to 127 bytes past the end of a fragment in the contiguous rx_bufs pool and leaves a net_buf whose len exceeds its capacity. The overflowing bytes are FIFO-underflow output rather than attacker-chosen data, so the practical impact is network-buffer-pool corruption and crashes rather than a controlled write. Only builds that enable CONFIG_IEEE802154_CC1200 with an attached CC1200 radio are affected."
}
],
"metrics": [
{
"cvssV3_1": {
"baseScore": 6.8,
"baseSeverity": "MEDIUM",
"vectorString": "CVSS:3.1/AV:A/AC:H/PR:N/UI:N/S:U/C:N/I:H/A:H",
"version": "3.1"
},
"format": "CVSS"
}
],
"problemTypes": [
{
"descriptions": [
{
"cweId": "CWE-787",
"description": "bounds",
"lang": "en",
"type": "CWE"
}
]
}
],
"providerMetadata": {
"dateUpdated": "2026-10-14T16:46:01.701Z",
"orgId": "e2e69745-5e70-4e92-8431-deb5529a81ad",
"shortName": "zephyr"
},
"references": [
{
"name": "Fix commit",
"tags": [
"patch"
],
"url": "https://github.com/zephyrproject-rtos/zephyr/commit/26a8b8294bf28523c7aa2f15cf728517980ee593"
},
{
"name": "GHSA-pgg5-wwxw-vmj8",
"url": "https://github.com/zephyrproject-rtos/zephyr/security/advisories/GHSA-pgg5-wwxw-vmj8"
}
],
"title": "Out-of-bounds write in the TI CC1200 IEEE 802.15.4 driver from an unvalidated radio-supplied packet length",
"x_generator": {
"engine": "cvelib 1.8.0"
}
}
},
"cveMetadata": {
"assignerOrgId": "e2e69745-5e70-4e92-8431-deb5529a81ad",
"assignerShortName": "zephyr",
"cveId": "CVE-2026-75084",
"datePublished": "2026-10-14T16:46:01.701Z",
"dateReserved": "2026-08-17T16:17:47.262Z",
"dateUpdated": "2026-10-14T16:46:01.701Z",
"state": "PUBLISHED"
},
"dataType": "CVE_RECORD",
"dataVersion": "5.2",
"vulnerability-lookup:meta": {
"epss": {
"cve": "CVE-2026-75084",
"date": "2026-10-15",
"epss": "0.00286",
"percentile": "0.19683"
},
"nvd": {
"cve": {
"affected": [
{
"affectedData": [
{
"collectionURL": "https://github.com/zephyrproject-rtos/zephyr",
"defaultStatus": "unaffected",
"packageName": "zephyr",
"product": "zephyr",
"programFiles": [
"drivers/ieee802154/ieee802154_cc1200.c"
],
"programRoutines": [
{
"name": "cc1200_rx"
},
{
"name": "read_rxfifo_content"
},
{
"name": "verify_rxfifo_validity"
}
],
"vendor": "zephyrproject",
"versions": [
{
"lessThanOrEqual": "4.4.2",
"status": "affected",
"version": "1.11.0",
"versionType": "semver"
}
]
}
],
"source": "vulnerabilities@zephyrproject.org"
}
],
"cveTags": [],
"descriptions": [
{
"lang": "en",
"value": "The CC1200 sub-GHz IEEE 802.15.4 driver takes the PHY packet length from the first byte of the radio\u0027s RX FIFO in get_packet_length() and validates it in verify_rxfifo_validity() (drivers/ieee802154/ieee802154_cc1200.c). That validation only enforced a lower bound (pkt_len \u003c 3); its second clause rejects a FIFO that holds more bytes than declared and therefore never bounds large values. Because the driver configures the radio for variable packet length with PKT_LEN = 0xFF, the length byte is an over-the-air value of 0-255 that reached net_pkt_rx_alloc_with_buffer() and the subsequent SPI burst read unclamped.\n\nAn unauthenticated attacker within radio range can transmit a frame that presents a length byte above the IEEE 802.15.4 maximum of 127 while the chip\u0027s 128-byte RX FIFO has not overflowed, so the driver\u0027s RX_FIFO_ERROR pre-check does not fire. Reaching this state depends on RF framing and timing, since the RX thread is driven off the PKT_SYNC_RXTX signal and may sample the FIFO before a packet is complete; no pairing, authentication, or user interaction is required.\n\nWith the default CONFIG_NET_BUF_FIXED_DATA_SIZE and CONFIG_NET_BUF_DATA_SIZE=128, an allocation larger than one fragment is satisfied by a chain of fragments, but read_rxfifo_content() performs a single SPI burst of pkt_len bytes into the first fragment\u0027s buf-\u003edata and then calls net_buf_add() with the same length. A length above 128 therefore writes up to 127 bytes past the end of a fragment in the contiguous rx_bufs pool and leaves a net_buf whose len exceeds its capacity. The overflowing bytes are FIFO-underflow output rather than attacker-chosen data, so the practical impact is network-buffer-pool corruption and crashes rather than a controlled write. Only builds that enable CONFIG_IEEE802154_CC1200 with an attached CC1200 radio are affected."
}
],
"id": "CVE-2026-75084",
"lastModified": "2026-10-15T14:46:15.327",
"metrics": {
"cvssMetricV31": [
{
"cvssData": {
"attackComplexity": "HIGH",
"attackVector": "ADJACENT_NETWORK",
"availabilityImpact": "HIGH",
"baseScore": 6.8,
"baseSeverity": "MEDIUM",
"confidentialityImpact": "NONE",
"integrityImpact": "HIGH",
"privilegesRequired": "NONE",
"scope": "UNCHANGED",
"userInteraction": "NONE",
"vectorString": "CVSS:3.1/AV:A/AC:H/PR:N/UI:N/S:U/C:N/I:H/A:H",
"version": "3.1"
},
"exploitabilityScore": 1.6,
"impactScore": 5.2,
"source": "vulnerabilities@zephyrproject.org",
"type": "Secondary"
}
]
},
"published": "2026-10-14T17:19:10.457",
"references": [
{
"source": "vulnerabilities@zephyrproject.org",
"url": "https://github.com/zephyrproject-rtos/zephyr/commit/26a8b8294bf28523c7aa2f15cf728517980ee593"
},
{
"source": "vulnerabilities@zephyrproject.org",
"url": "https://github.com/zephyrproject-rtos/zephyr/security/advisories/GHSA-pgg5-wwxw-vmj8"
}
],
"sourceIdentifier": "vulnerabilities@zephyrproject.org",
"vulnStatus": "Awaiting Analysis",
"weaknesses": [
{
"description": [
{
"lang": "en",
"value": "CWE-787"
}
],
"source": "vulnerabilities@zephyrproject.org",
"type": "Secondary"
}
]
}
}
}
}
Loading…
Loading…
Drag nodes to arrange them. Double-click a related vulnerability to open it, or a source to visit its link. The Physics button on the left tunes the layout and the simulation; the legend at the bottom left hides or shows nodes by kind and by sighting type.
Experimental. This forecast is provided for visualization only and may change without notice. Do not use it for operational decisions.
Forecast uses a logistic model when the trend is rising, or an exponential decay model when the trend is falling. Fitted via linearized least squares.
Sightings
| Author | Source | Type | Date | Other |
|---|
Nomenclature
- Seen: The vulnerability was mentioned, discussed, or observed by the user.
- Confirmed: The vulnerability has been validated from an analyst's perspective.
- Published Proof of Concept: A public proof of concept is available for this vulnerability.
- Exploited: The vulnerability was observed as exploited by the user who reported the sighting.
- Patched: The vulnerability was observed as successfully patched by the user who reported the sighting.
- Not exploited: The vulnerability was not observed as exploited by the user who reported the sighting.
- Not confirmed: The user expressed doubt about the validity of the vulnerability.
- Not patched: The vulnerability was not observed as successfully patched by the user who reported the sighting.
Vulnerability timeline
Sightings and recorded dates, grouped by day · UTC
Loading timeline…
Loading…
Loading…
The MITRE ATT&CK techniques below are AI-generated suggestions, inferred from the description of the
vulnerability by the CIRCL/vulnerability-attack-technique-classification-roberta-base
model, served locally by ML-Gateway.
They have not been verified by an analyst and are provided for guidance only.
The approach is described in our paper Mapping CVEs to MITRE ATT&CK Techniques: A Curated Gold-Set Classifier and the Limits of LLM-Assisted Label Expansion.
Browse all ATT&CK techniques and the vulnerabilities related to each.
The approach is described in our paper Mapping CVEs to MITRE ATT&CK Techniques: A Curated Gold-Set Classifier and the Limits of LLM-Assisted Label Expansion.
Browse all ATT&CK techniques and the vulnerabilities related to each.
Loading…
Related by attack behaviour
Vulnerabilities whose description is nearest to this one in the vector space of the CIRCL/vulnerability-attack-technique-biencoder model. This is a similarity search over the bi-encoder space (plain cosine), not a classification, and it has no measured accuracy.