In the Linux kernel, the following vulnerability has been resolved:

Bluetooth: hci_qca: Do not write to the serial port after it is closed

hci_uart_close() closes the serdev port if HCI_QUIRK_NON_PERSISTENT_SETUP is set (for example, for the WCN399x family). A failed hci_dev_open_sync() following a successful qca_setup() calls hdev->close() but not hdev->shutdown(), so the port is closed while power->vregs_on is left true. qca_serdev_remove() then passes its power->vregs_on test and calls qca_power_off(), which writes to the closed port unconditionally.

Seen on a WCN3988 by unbinding the driver after a controller failure. The trace below is from a 7.0.0 based kernel, where qca_power_off() was still named qca_power_shutdown():

Unable to handle kernel NULL pointer dereference at virtual address 0000000000000038 Call trace: tty_set_termios+0x50/0x238 (P) ttyport_set_baudrate+0x84/0xc0 serdev_device_set_baudrate+0x24/0x40 qca_power_shutdown+0x158/0x1fc [hci_uart] qca_serdev_remove+0x54/0x68 [hci_uart] serdev_drv_remove+0x1c/0x2c device_remove+0x4c/0x80 device_release_driver_internal+0x1cc/0x224 device_driver_detach+0x18/0x24 unbind_store+0xb4/0xc0

Check HCI_UART_PROTO_READY, which hci_uart_close() clears in the same place it closes the port, before writing to it. The regulator disable is left unconditional so the controller is still powered down.

The dangling serport->tty that turns this into a use-after-free is addressed in a separate p…

In the Linux kernel, the following vulnerability has been resolved:

Bluetooth: hci_qca: Do not write to the serial port after it is closed

hci_uart_close() closes the serdev port if HCI_QUIRK_NON_PERSISTENT_SETUP is set (for example, for the WCN399x family). A failed hci_dev_open_sync() following a successful qca_setup() calls hdev->close() but not hdev->shutdown(), so the port is closed while power->vregs_on is left true. qca_serdev_remove() then passes its power->vregs_on test and calls qca_power_off(), which writes to the closed port unconditionally.

Seen on a WCN3988 by unbinding the driver after a controller failure. The trace below is from a 7.0.0 based kernel, where qca_power_off() was still named qca_power_shutdown():

Unable to handle kernel NULL pointer dereference at virtual address 0000000000000038 Call trace: tty_set_termios+0x50/0x238 (P) ttyport_set_baudrate+0x84/0xc0 serdev_device_set_baudrate+0x24/0x40 qca_power_shutdown+0x158/0x1fc [hci_uart] qca_serdev_remove+0x54/0x68 [hci_uart] serdev_drv_remove+0x1c/0x2c device_remove+0x4c/0x80 device_release_driver_internal+0x1cc/0x224 device_driver_detach+0x18/0x24 unbind_store+0xb4/0xc0

Check HCI_UART_PROTO_READY, which hci_uart_close() clears in the same place it closes the port, before writing to it. The regulator disable is left unconditional so the controller is still powered down.

The dangling serport->tty that turns this into a use-after-free is addressed in a separate p…

kernel-devel-7.2.10-1.1 on GA media

Affected: Ubuntu:16.04:LTS: linux-hwe-edge, Ubuntu:18.04:LTS: linux-aws-5.0, Ubuntu:18.04:LTS: linux-aws-5.3, Ubuntu:Pro:18.04:LTS: linux-aws-5.4, Ubuntu:18.04:LTS: linux-azure, Ubuntu:18.04:LTS: linux-azure-5.3, Ubuntu:Pro:18.04:LTS: linux-azure-5.4, Ubuntu:18.04:LTS: linux-azure-edge, Ubuntu:18.04:LTS: linux-gcp, Ubuntu:18.04:LTS: linux-gcp-5.3 and 220 more

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: hci_qca: Do not write to the serial port after it is closed hci_uart_close() closes the serdev port if HCI_QUIRK_NON_PERSISTENT_SETUP is set (for example, for the WCN399x family). A failed hci_dev_open_sync() following a successful qca_setup() calls hdev->close() but not hdev->shutdown(), so the port is closed while power->vregs_on is left true. qca_serdev_remove() then passes its power->vregs_on test and calls qca_power_off(), which writes to the closed port unconditionally. Seen on a WCN3988 by unbinding the driver after a controller failure. The trace below is from a 7.0.0 based kernel, where qca_power_off() was still named qca_power_shutdown(): Unable to handle kernel NULL pointer dereference at virtual address 0000000000000038 Call trace: tty_set_termios+0x50/0x238 (P) ttyport_set_baudrate+0x84/0xc0 serdev_device_set_baudrate+0x24/0x40 qca_power_shutdown+0x158/0x1fc [hci_uart] qca_serdev_remove+0x54/0x68 [hci_uart] serdev_drv_remove+0x1c/0x2c device_remove+0x4c/0x80 device_release_driver_internal+0x1cc/0x224 device_driver_detach+0x18/0x24 unbind_store+0xb4/0xc0 Check HCI_UART_PROTO_READY, which hci_uart_close() clears in the same place it closes the port, before writing to it. The regulator disable is left unconditional so the controller is still powered down. The dangling serport->tty that turns this into a use-after-free is addressed in a separate patch.